Nomex High-Temp Replacement Complete Gasket Kit for Lg XL Big Green Egg Ceramic Lid Top

I used the Nomex Gasket kit for my flowerpot smoker and it worked flawlessly. Easy to install, created a great seal and was a good price.

Applied these a few months ago and they work as expected, no better or worse than the factory ones. If you are new to replacing your gaskets, just take the lid completely off and make sure you clean the rims extremely thoroughly. Start with a scraper to remove the old one and any excess adhesive. Then follow up with a degreaser and a wire brush. Keep wiping it off with paper towels and scrubbing. Once it's clean, wipe it down a few more times with Simple Green or another surface cleaner, then follow up with rubbing alcohol to remove any residual oils and moisture. The paper towels should come out clean, no brown or black should be wiping off. If they aren't coming out clean, keep cleaning until they do. BBQ pits are very, very dirty, so expect to spend 30-60 minutes doing this, depending on how dirty yours is and how many remnants of the old gasket/adhesive are left behind. It sucks, but you should only have to do it every 5 years or so. Applying the new gaskets is pretty easy, just slowly peel the backing off as you are pressing it on the rim. do not remove the backing all at once or it could stick to the side of the BGE or to itself, which could potentially ruin them. Just slowly remove a couple inches at a time. Do not stretch or compress it, just push it straight down. When you get to the end of the circle, cut it with a scissors, but give yourself an inch of extra slack. Incrementally cut small pieces off until it's exactly the right length. Do this very deliberately because you don't want any gap or overlap. Repeat for the other rim. When they're both in place, spend a couple minutes pressing down very firmly with your hands, all the way around. Reattach lid and close it. I like to let it sit for at least a day before using, to give the adhesive time to bond. It may sound like I'm being obsessive here, but having screwed up BGE gaskets a couple times, I'm telling you all of this from experience. I've had a BGE for nearly 20 years. I've replaced them 6 times and screwed up 2 of those times. The surface preparation is critical to adhesion. Gaps, overlap or compromising the adhesive can and will lead to leaks or even the gaskets completely falling off. Negative reviews are most likely a result of inadequate cleaning or bunching/stretching the gaskets. It is a dirty and annoying job, so do it right the first time, because you don't want to have to do it again a couple months down the road.

I just ordered another one, after 9 years. The original LavaLock I purchased back in 2016 was a replacement for the OE gasket that came with my BGE. The original BGE gasket only made it about 5 years before it needed to be replaced. The LavaLock gasket never let smoke/heat out, etc., even after 9 years. The only reason I'm replacing the gasket is because I'm building an outdoor kitchen, so, to move it from my old mobile BGE table to the new outdoor kitchen by myself, I needed to take the dome off. When I did, I noticed that the 9-year-old LavaLock gasket wasn't adhering as well as it originally did. Great product. It's nice to still have some products available that are well-made and durable.

Nice replacement, slightly thicker than OEM

After reading mixed reviews, i decided to try it, it is just a piece of sticky felt and I didnt see the need in spending big bucks on it. If it isnt sticking, then I assume you didnt clean the bge well enough for it to stick. I spent about an hour scrubbing and scraping using degreaser, then cleaned it with rubbing alcohol. It applied easily i just used my finger on the inside edge as a guide and peeled the backing as i went. Pulled it tight as I went but didn't stretch it. Made a perfect seal and stuck so far. Installed on a saturday morning, then that night started a 7 hour smoke .... worked perfect, stuck perfect. Overlapped the edges then trimmed them down with a razor to get a tight fit at the seam.

Replaced OEM with this and it works great. Plenty of tape for the bottom, top, and cap. Quality seems as good as OEM or better. Can't beat the price. One long roll. Just cut as you use. Get a can of Acetone, pour it on old gasket and it will peal off like an old band aid. Use a paint scraper, get it all off. Wipe it dry. Wait 1 minute and starting from the back unroll it. When you reach the end clip it slowly to get a perfect fit. Don't pull or stretch while laying down. After complete push down on tape with round part of screwdriver post.

Good stuff. Easy install. Got a little extra with it. I will buy again for large green egg.

Fit my large BGE perfectly with some to spare.

Replaced the gasket on our bge. Was more than enough for the large size and easy to apply.

facil de instalar

Leicht zu montieren, Reicht für oben und unten. Viel schöner als die alte Ofendichtung, viel dichter da dicker. sehr schöne dicke Abdichtung Die Temperaturbeständigkeit muss sich noch erweisen, da bisher nur bei 160 Grad gesmoket Preis nicht ganz billig ist es aber wert.

this is enough to do both lid surfaces and chimney with an extra 18" to spare. Haven't tried it yet, but it seems like decent quality. 4 stars as the adhesive feels like it wants to pull away. I'm sure after a decent smoke to set it it'll stay in place. I don't expect more than 2 years from a gasket, but will be pleased if I get a 3rd

Despite what the sellers said in the Q & A, this is not a proper fit for mini max. It’s too wide.