OD 6" Ultimate Handwheel for Any Machine, Fits 3/4" (19.10mm) Shaft or Smaller, Ideal for Table Saw, Milling Machine, Lathe, Drill Press, Tailstock, Liquid Filling Equipment – Made in Korea

Handwheel – Outside Diameter 5.5" -- 1/2" holeThe factory table height adjustment crank on my Jet J-2530 15" Bench Drill Press flexed when raising the table with a heavy 4" cross vise. Not wanting to wait until the handle broke, I replaced it with one of these fine hand-wheels.The black plastic on this handwheel is unusually thick, the aluminum hub is substantial, the hub is tightened with three set screws (included) versus one on the competition, and it is expertly manufactured. E.g., the aluminum is 5/16" thick where it’s threaded for the set screws. The shaft hole is 7/8" deep, which matched the length of the Jet bench press shaft.If the shaft for where you will install the handwheel is ½" in diameter, simply attach this, and you're good to go.In my case, the Jet table crank shaft is .564 in diameter, which is essentially 9/16" (0.5625") -- so the hand wheel’s aluminum 1/2" hole needed to be slightly enlarged. Here's one way to do that, ensuring that the enlarged hole remains perpendicular to the piece:1. Cut a supporting "base" out of plywood (e.g., 1/2" thick) the same size as the hand wheel’s outside diameter – 5.5" x 5.5" in my case. Screw that to a scrap piece of 2x4.2. Clamp that 2x4 onto a drill press's vise. (If your drill press doesn’t have a vice or cross vise, skip the 2x4 and clamp the base directly onto the drill press table.)3. Set the handwheel on the base and hold it down with six spring clamps. Don’t over tighten, if using stronger clamps, to avoid cracking the plastic.4. Using a the proper sized drill bit (9/16" in my case) -- lower the bit to where it would just begin cutting and set the drill's depth stop to 7/8" (depth of the handwheel hole) from there. Be sure not to drill too big a hole, so the hand wheel doesn’t wobble.5. Set the drill’s speed to a slow speed. This is usually done by moving its drive belts.6. Align the bit with the hole and slowly enlarge it to the drill’s size, down to the depth stop.7. Install the Allen screws and make sure they screw in past the resized hole – clean up any aluminum flakes from around the threads.8. Slip the handwheel onto the crank shaft leaving a slight gap from the machine so that it doesn't bind -- tighten the Allen screws onto the crank shaft; install the handle.If the hole is too tight (after drilling out) to slip onto the crank shaft, put a Dremel-sized sanding disk in the drill and incrementally enlarge said hole until it fits.See Customer Images...

I wish it were a little cheaper but this hand wheel was exactly what i needed, installed easily and is very well made. Love it!

I don't usually get too excited about functional components, but I have to make an exception here.I needed a replacement handle for the table lift on my drill press. I didn't like the OEM crank arm and wanted something round. This was exactly what I was looking for and I'm glad I purchased it. It was easily adapted to my drill press and is so much nicer to use than the old crank handle.

The handle to raise and lower my ridgid radial arm saw broke in half. This design makes it a direct replacement for the original part, which can not be obtained from the manufacturer or other sites. The added benefit of this part is that it raises and lowers the arm with less effort than before. The diameter is small enough whereas to not rack my knuckles as I spin it. If anyone needs to get a replacement like this, I would highly recommend that you at least consider this part for the operation in which you need.

This is a well-made and easy to install miniature Patton tank! Works fantastic and beats the crap out of the S-F factory's installed crank it replaced. Good buy!

Works great as a replacement for the broken handle on my fireplace damper.

This hand-wheel is very well designed and flexible to use/install on tools that need a hand-wheel to control movement. I was very happy to see that someone made this add-on hand-wheel for tools where an OEM manufacturer decided to cut costs and didn't include one.The plastic handle is thick and appears to be quite strong. I loved that the provider included (2) sets of the (3) "set screws" that engage the Aluminum cylinder and hold the hand-wheel to a post. The people that designed this add-on part have shown that they understand how a tool like this is used and how to design it for function. Good job!

I've been eyeballing these for months. Get it. I used mine to replace an undersized tailstock hand wheel. Now when I need to spend several hours a day boring out materials with the tailstock, my hands and forearms hurt way way less. The large handwheel provides some much more leverage, and the smooth design saves your hands from getting friction sores.

I bought 4 hand wheels for a machine retrofit where I work. These 140mm hand wheels seem solid and strong in the hand and will make doing adjustment much easer. The web plastic between the hub and outer ring is quite a bit thicker than I was expecting. I was limited for space but this diameter is still big enough to provide enough torque to make the adjustments. I like that there are three set screws to replace the three cap screws to secure the wheel to the shaft.The seller was very prompt to reply to any communication.Update-the added picture is with the hand wheels install on the pipe fuser. The three set screws grip the threaded shaft better than I expected.

Produkt wurde für Holzdrehbankspindel verwendet, Teil war nirgends zu bekommen, durch Zufall kam ich auf die Firma DONDYANG, hier wurde mir Per Mail technisch alles besprochen und Sonderteil kam in 14 Tagen. Firma kann ích nur bestens empfehlen, sehr korrekt und freundlich, Danke.

Very good quality, i've purchase this many times.great communication from the supplier. Will buy again when i need it.

Alles super gelaufen. Vielen Dank.

Nice tight fit on my plain half inch spindle (might not bother installing the set screws)